Stable Environment : Ensure the installation site is free from excessive vibration and within the operating temperature range of 5∘C5 raised to the composed with power C to 45∘C45 raised to the composed with power C ( 41∘F41 raised to the composed with power F to 113∘F113 raised to the composed with power F ). Power Supply : Requires a grounded electrical outlet (100–240 VAC, 50/60 Hz). Space Requirements : Allow at least 200mm (8 inches) of clearance around the printer for ventilation and door access. Mechanical Installation Mounting : Secure the printer to a Videojet-approved floor stand or a stable tabletop. Ensure it is level to maintain proper ink pressure. Printhead Placement : Position the printhead on its bracket. The printhead should ideally be at the same level as, or lower than, the printer cabinet. Umbilical Routing : Ensure the umbilical (the cable connecting the cabinet to the printhead) has no sharp bends or kinks. The minimum bend radius is typically 150mm (6 inches). Fluid Setup Insert Cartridges : Open the fluid door and insert the Videojet SmartCart ink and make-up cartridges. Engagement : Push the cartridges until they click into place. The printer's needle system will automatically pierce the septum. Priming : Follow the on-screen prompts on the SIMPLICiTY™ interface to prime the ink system. This may take several minutes during the initial startup. Electrical & Data Connections Ethernet/USB : Connect to your local network via the Ethernet port or insert a USB drive for job transfers. Product Sensor : Plug the photocell (product sensor) into the designated port to trigger printing. Shaft Encoder : If line speed varies, connect an encoder to the printer's auxiliary port to ensure consistent code width. Software Configuration Power On : Use the switch on the side of the cabinet. Wizard Setup : Use the guided "Installation Wizard" on the touchscreen to set the date, time, and language. Nozzle Aiming : Use the "Clean Start" feature to check the ink stream alignment. Ensure the stream is centered in the gutter. Official Resource: To download the complete, authorized Videojet 1280 Operator Manual , visit the Videojet Document Support Center or use the QR code found inside the printer’s cabinet door to access mobile-friendly documentation.
Installing a Videojet 1280 is designed to be a straightforward process, often guided by the on-board SIMPLICiTY™ touchscreen interface rather than just a traditional paper manual. Videojet US Here is the "story" of how a typical installation and setup unfolds based on official technical guides: 1. Preparing the Workspace Before powering on, ensure the environment meets these critical specs: You need a standard 100-240 VAC supply (50/60 Hz). Environment: The unit is IP55 rated, meaning it handles dust and some water ingress, but it performs best between 32°F and 122°F (0°C to 50°C) with non-condensing humidity. The dry unit weighs about 39.5 lbs (17.9 kg), so it requires a stable, grounded mount near the production line. Videojet US 2. Initial Connection & Power Safety First: Use only the provided three-pole mains cable with a protective ground. Once plugged in, the 8-inch touchscreen will boot to the home screen. If the status bar shows "PRINTER OFF," you are ready to begin the startup sequence. 3. Startup & Fluid Loading Videojet® 1280
Videojet 1280 is designed for simplified user-performed installation and maintenance, featuring an intuitive SIMPLICiTY™ touchscreen interface with on-board "how-to" videos. Videojet US Manual & Resource Downloads Official documentation for the Videojet 1280 can be accessed through the Videojet Document Hub . Key files typically available include: Videojet Technologies Operator Manual : Provides detailed instructions on startup, login, and basic job setup. Specification Sheet : Covers electrical requirements (100-240 VAC) and physical dimensions. Technical Training Guide : Often used for more advanced setup and troubleshooting. Basic Installation & Setup Steps Physical Inspection : Ensure all cables and connections are properly secured before powering on. : Use the power button on the back of the machine; wait for the main screen to load. Initial Login : Tap the role bar to select a username and enter your password. Environmental Calibration : The printer uses Dynamic Calibration™ to automatically adjust jetting parameters based on ambient conditions. SmartCell™ Setup : If installing a new module, ensure the Videojet SmartCell™ service module is correctly seated; it is designed for tool-free replacement in under 5 minutes. Quick Specifications 1280, 1240 Technical Training Guide - 01 - AA - Scribd
How to Find & Use the Videojet 1280 Manual PDF for Installation If you’ve just purchased a Videojet 1280 (or are maintaining an existing one), you know it’s a powerhouse in the continuous inkjet (CIJ) world. But before you start printing expiration dates or lot codes, you need to get it set up correctly. The official Videojet 1280 manual PDF is your best friend during installation. Here is everything you need to know about finding the right document and the key steps for setting up this industrial printer. Where to Find the Official PDF Warning: Avoid random PDF hosting sites. Manuals change, and old versions may have incorrect wiring diagrams. videojet 1280 manual pdf install
The Official Source (Best Option): Go directly to the Videojet Exchange portal (my.videojet.com). You will need to register your printer’s serial number to access the specific “User Manual” and “Installation Guide.” The QR Code: Scan the QR code located on the side of the printer cabinet. This links directly to the current documentation for your specific firmware version. Google Search Trick: Use exact phrases like: "Videojet 1280" "Installation Guide" filetype:pdf
Pro Tip: You are looking for two specific documents: The Site Preparation Guide (for electrical/air requirements) and the Operator Manual (for physical setup).
Key Installation Steps from the Manual Once you have the PDF open, pay close attention to these three critical areas. Skipping them is the #1 cause of installation errors. 1. Environmental Requirements (Chapter 1) The 1280 is sensitive to its surroundings. The manual specifies: Stable Environment : Ensure the installation site is
Temperature: 40°F to 104°F (5°C to 40°C). Dust: Keep it away from conveyor belts that kick up flour, dust, or debris. Vibration: Do not mount it directly to a vibrating conveyor. Use a stand-alone table.
2. Fluid Handling (The "Bottle Swap") Unlike smaller printers, the 1280 uses a bag-in-box system.
The Manual shows: How to connect the make-up bottle (low viscosity) and the printer bottle (ink). Critical Step: You must remove the shipping bracket (page 24 of most versions) before turning on the pump. If you miss this, the pump will stall. Mechanical Installation Mounting : Secure the printer to
3. Electrical & Grounding (Safety First)
Voltage: Confirm 100-240 VAC (autosensing, but check the label). Grounding: The 1280 requires a dedicated earth ground. A floating neutral will cause print quality issues and error codes.
We’re always in search for talented and motivated people. Don’t be shy introduce yourself!